Megger MIT300-EN Insulation Tester, 1000 Megaohms Resistance, 250V, 500V Test Voltage
Free Shipping Included! Megger MIT300-EN Insulation Tester, 1000 Megaohms Resistance, 250V, 500V Test Voltage by Megger at Web Natin. MPN: MIT300-EN. Hurry! Limited time offer. Offer valid only while supplies last. The Megger MIT300 series insulation resistance tester measures insulation resistance, voltage, and continuity in electrical installations, building
The Megger MIT300 series insulation resistance tester measures insulation resistance, voltage, and continuity in electrical installations, building maintenance, and electrical testing. The average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform. The dual LCD screen indicates test results either digitally or with an analog arc function to replicate the response of analog meters. The tester measures insulation resistance from 0 to 1,000 megohms, voltage from 0 to 600V, and continuity from 0.01 to 100 ohms. The unit has a test inhibit function that prevents testing on circuits carrying over 50V. The tester is safety rated to European Standard EN61010-1, Category III, 600V. The unit is also Ingress Protection 54 (IP54)-rated for protection against dust and splashing water. The unit has a rubberized outer case for protection against bumps and short drops. The Megger MIT300 series is commonly used by electricians and electrical contractors.
|Continuity testing range||0.01 to 100 Ohms|
|Insulation resistance range||0 to 1,000 megohms|
|Voltage testing range||0 to 600V AC/DC|
|Voltage test inhibit level||50V|
|Power supply||8 AA alkaline or rechargeable batteries|
|Safety standard met||International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat III 600V|
|Mechanical standard met||IP54, for protection from dust and splashing water|
|Dimensions||203 x 148 x 78mm / 8 x 5.7 x 3.2 inches|
H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. An electrical test meter has multiple settings corresponding to potential ranges of values for the properties it can measure. A manual ranging meter requires the operator to flip through different settings until the correct range is reached. An autoranging meter cycles through range settings automatically until it reaches the correct range.
Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardization (ISO) 9001:2008 standards.
What’s in the Box?
- MIT300 Series Insulation and Continuity Tester
- (1) Test lead set with croc clips
Features & Highlights
- Insulation tester for testing insulation resistance, voltage, and continuity in electrical installations
- Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform
- Dual digital display with analog arc function to replicate response of analog meters
- Measures insulation resistance from 0 to 1,000 megohms, voltage from 0 to 600V, and continuity from 0.01 to 100 ohms
- Safety rated to European Standard EN61010-1 Category III, 600V and IP54 rated for protection against dust and splashing water
|Item Weight:||2.16 pounds|
|Package Weight:||4.85 pounds|
|Package Size:||11 x 4.3 x 4.3 inches|